Protocol for Extraction and Purification of Genomic DNA from Cells (NEB #T3010)

Below is a detailed protocol containing explanations and commentary. If you prefer a more concise protocol, please use our Quick Protocol or download our Quick Protocol Card.

Before You Begin:

  • Store RNase A and Proteinase K at -20°C.
  • Add ethanol (≥ 95%) to the Monarch gDNA Wash Buffer concentrate as indicated on the bottle label.
  • Cold PBS (not supplied) is required for processing cultured cells
  • Set a thermal mixer (e.g. ThermoMixer® or similar device), or a heating block to 56°C for sample lysis.
  • Set a heating block to 60°C. Preheat the appropriate volume of elution buffer to 60°C (35–100 μl per sample). Confirm the temperature, as temperatures are often lower than indicated on the device.
  • Do not load a single column with the lysed sample more than once; over-exposure of the matrix to the lysed sample can cause the membrane to expand and dislodge.

Genomic DNA Purification Consists of Two Stages:

PART 1: Sample Lysis

PART 2: Genomic DNA Binding and Elution



Please follow the protocol specific to your starting material:

Cultured Cells

  1. Start with a cell pellet containing 1 x 104 – 5 x 106 cells (typical starting amount is 1 x 106 cells). If using lower cell inputs, the use of carrier RNA may be beneficial, see “Use of Carrier RNA for Low Input Amounts” in the product manual.

    • Frozen cell pellets: thaw pellet slowly on ice and loosen by flicking the tube several times. Add 100 μl cold PBS and resuspend by carefully pipetting up and down 5–10 times. Ensure pellet is resuspended completely.

    • Fresh cells: pellet cells by centrifugation at 1000 x g for 1 minute. Remove supernatant and resuspend in 100 μl cold PBS by carefully pipetting up and down 5-10 times. Ensure pellet is resuspended completely.

  2. Add 1 μl Proteinase K and 3 μl RNase A to the resuspended pellet and mix by vortexing briefly to ensure the enzymes are efficiently dispersed. Do not add the enzymes and the Cell Lysis Buffer simultaneously, as the high viscosity of the lysate will prevent equal distribution of the enzymes. Addition of RNase A can be omitted if a low percentage of co-purified RNA will not affect downstream applications. For greater convenience in pipetting, working aliquots of the Proteinase K stock can be diluted 5X. Determine how much Proteinase K you need for your preps and mix this amount of enzyme with 4 volumes of nuclease-free water or PBS. Do not use EDTA-containing buffers like TE. Add 5 μl of this 5X dilution to the resuspended cells and proceed as indicated above.

  3. Add 100 μl Cell Lysis Buffer and vortex immediately and thoroughly. The solution will rapidly become viscous.

  4. Incubate for 5 minutes at 56°C in a thermal mixer with agitation at full speed (~1400 rpm). If an incubator with agitation is not available, use a heating block and vortex once or twice during the incubation. Incubation for longer than 5 minutes is not necessary, but will not negatively affect the quality of the purified gDNA.

  5. Proceed to Step 1 of Part 2: Genomic DNA Binding and Elution.



  1. Add 400 μl gDNA Binding Buffer to the sample and mix thoroughly by pulse-vortexing for 5-10 seconds. Thorough mixing is essential for optimal results.

  2. Transfer the lysate/binding buffer mix (~600 μl) to a gDNA Purification Column pre-inserted into a collection tube, without touching the upper column area. Proceed immediately to step 3. Do not reload the same column with more sample; over-exposure of the matrix to the lysed sample can cause the membrane to expand and dislodge. Avoid touching the upper column area with lysate/binding mix and avoid transferring foam that may have formed during lysis. Any material that touches the upper area of the column, including any foam, may lead to salt contamination in the eluate.

  3. Close the cap and centrifuge: first for 3 minutes at 1,000 x g to bind gDNA (no need to empty the collection tubes or remove from centrifuge) and then for 1 minute at maximum speed (> 12,000 x g) to clear the membrane. Discard the flow-through and the collection tube. For optimal results, ensure that the spin column is placed in the centrifuge in the same orientation at each spin step (for example, always with the hinge pointing to the outside of the centrifuge); ensuring the liquid follows the same path through the membrane for binding and elution can slightly improve yield and consistency.

  4. Transfer column to a new collection tube and add 500 μl gDNA Wash Buffer. Close the cap and invert a few times, so that the wash buffer reaches the cap. Centrifuge immediately for 1 minute at maximum speed (12,000 x g), and discard the flow through. The collection tube can be tapped on a paper towel to remove any residual buffer before reusing it in the next step. Inverting the spin column containing wash buffer prevents salt contamination in the eluate.

  5. Reinsert the column into the collection tube. Add 500 μl gDNA Wash Buffer and close the cap. Centrifuge immediately for 1 minute at maximum speed (>12,000 x g), then discard the collection tube and flow through.

  6. Place the gDNA Purification Column in a DNase-free 1.5 ml microfuge tube (not included). Add 35-100 μl preheated (60°C) gDNA Elution Buffer, close the cap and incubate at room temperature for 1 minute. Elution in 100 μl is recommended, but smaller volumes can be used and will result in more concentrated DNA but a reduced yield (20–25% reduction when using 35 μl). Eluting with preheated elution buffer will increase yields by ~20–40% and eliminates the need for a second elution. For applications in which a high DNA concentration is required, using a small elution volume and then eluting again with the eluate may increase yield (~10%). The elution buffer (10 mM Tris-Cl, pH 9.0, 0.1 mM EDTA) offers strong protection against enzymatic degradation and is optimal for long term storage of DNA. However, other low-salt buffers or nuclease-free water can be used if preferred. For more details on optimizing elution, please refer to “Considerations for Elution & Storage” in the product manual.

  7. Centrifuge for 1 minute at maximum speed (> 12,000 x g) to elute the gDNA. 


Additional Resources you may find helpful:

  1. Lysis Tips

    Post-lysis Tips for Optimal Results using the Monarch® Genomic DNA Purification Kit

    After lysing your sample during your DNA extraction workflow, follow these tips to ensure that your purified gDNA is high-quality, intact, and free from contaminants.